ComMarker B4 60W JPT MOPA Fiber Laser vs GWEIKE G2 20W Fiber Laser Engraver
Head-to-head spec comparison to help you pick the right fiber laser for your needs.
ComMarker
$1099
GWEIKE
$499
Spec-by-Spec Comparison
| Spec | ComMarker B4 60W JPT MOPA Fiber Laser | GWEIKE G2 20W Fiber Laser Engraver |
|---|---|---|
| Wattage | 60 W | 20 W |
| Laser Type | MOPA | Q-Switched |
| Laser Source | JPT | Raycus |
| Work Area (W) | 175 mm | 110 mm |
| Work Area (H) | 175 mm | 110 mm |
| Galvo Speed | 10000 mm/s | 15000 mm/s |
| Color Marking | Yes | No |
| LightBurn | Yes | Yes |
| Autofocus | No | No |
| Weight | 5.5 kg | 2.5 kg |
| Software | LightBurn + EZCad2 (LightBurn requires COR file setup) | LightBurn + EZCad2 |
| Pulse Width | 2–500ns | N/A (Q-Switched) |
| Price | $1099 | $499 |
| Rating | 9.0/10 | 7.8/10 |
| Buy on Amazon | Buy on Amazon |
Pros & Cons
ComMarker B4 60W JPT MOPA Fiber Laser
Pros
- JPT M7 MOPA source confirmed — wider frequency range (1–4,000kHz) and tighter pulse consistency than Raycus Q-switched alternatives at any price; the datasheet comes in the box
- 60W output at up to 10,000mm/s makes batch tumbler marking and production jewelry engraving run at business-viable throughput — no other LightBurn-compatible MOPA under $1,100 offers this combination
- LightBurn compatible via COR file — both LightBurn and EZCad2 workflows supported; JPT M7's full pulse-width parameter range is accessible from LightBurn's galvo interface once configured
- Rust cleaning at 60W is a documented bonus capability — removes surface oxide from steel without abrasives, useful as pre-treatment before color marking on weathered material
- Foot pedal input, job preview function, and fan that only runs during active engraving — the small-business production workflow details that distinguish a tool from a toy
Cons
- LightBurn setup requires loading a COR file and manually configuring galvo axis, Q-Pulse Width, and frequency settings — LightBurn forum (April 2026) shows new owners needing 30+ minutes before getting first correct results; not auto-detected
- No autofocus — manual Z-axis focus required for every workpiece height change; the B6 MOPA, ComMarker's current flagship, corrects this limitation
- B4 MOPA line is end-of-life inventory — ComMarker now promotes the B6 MOPA (autofocus, updated form factor, same 60W power); ASIN B0CGX9TBGQ remains on Amazon but community resources will increasingly reference the B6 going forward
- Color marking requires calibration per material batch — powder coat thickness and alloy composition vary even within the same tumbler brand, requiring fresh test grids for each new batch
- No enclosure — Class 4 open-beam 1064nm infrared; requires OD6+ eyewear at 60W and either ComMarker's Safety Enclosure Pro or a dedicated controlled workspace
GWEIKE G2 20W Fiber Laser Engraver
Pros
- LightBurn native at $499 — GWEIKE actively maintains their galvo driver; owners moving from diode lasers report zero learning curve on software setup
- 15,000mm/s galvo speed confirmed across all sources — 50% faster than the Monport 20W at $150 more; the throughput gap is measurable on any design with infill
- Raycus 20W source with documented reliability in knife-marking communities — a dedicated Italian cutlery review site (coltellimania.com, 14k views) independently validated the G2 for blade work
- 110×110mm work area covers rings, blade sections, small plaques, and coin marking without repositioning or compromising mark quality
- Active settings ecosystem: YouTube tutorials, LightBurn forum threads, and community settings libraries are indexed for the G2 specifically — problems you hit have been solved publicly
Cons
- Power-loss mid-job defect documented on LightBurn forum (June 2025) — mid-engraving power drop reported on some units; a workaround exists in settings but not every owner encounters it
- Customer service is WhatsApp-only with slow US response times — if something goes wrong, you are on your own until business hours in China; not viable for production-critical downtime
- Focus height calibration is poorly documented — community consensus is to calibrate by burn quality and sound rather than ruler measurement; GWEIKE's manual understates this complexity
- 110×110mm work area rules out tumblers and anything wider than a palm — if typical work pieces are over 100mm, step up to the ComMarker B6 (150mm field)
- No color marking — Q-switched laser cannot produce oxidation colors on stainless steel regardless of settings
Our Verdicts
ComMarker B4 60W JPT MOPA Fiber Laser
The ComMarker B4 60W MOPA earns the top rating because no other machine under $1,100 combines 60W JPT MOPA, LightBurn support, and a work area that handles tumblers. It is the benchmark for serious makers and small business operators. Two things to verify before buying: first, check whether ASIN B0CGX9TBGQ is in stock — the B4 line is end-of-life, and if both the B4 and B6 MOPA are available at similar prices, the B6's autofocus makes it the stronger long-term buy. Second, budget time for LightBurn setup — the COR file configuration takes an hour the first time. For experienced users who know what they are buying into, this remains the benchmark purchase under $1,100.
GWEIKE G2 20W Fiber Laser Engraver
The GWEIKE G2 20W is the best 20W entry-level fiber laser for a buyer who wants LightBurn from day one and values community documentation over price. At $499 it costs $150 more than the Monport 20W, and that premium buys a 50% galvo speed improvement, a driver that GWEIKE actively maintains, and a community that has already solved the problems you will encounter. The constraint is the 110mm work area: sufficient for jewelry, knife sections, and small items, but not for tumblers or anything wider. If work fits in 110mm and you want the smoothest entry into fiber, this is the pick. If work area matters, pay $100 more for the ComMarker B6 at 150mm.